Page 327 - MISUMI Thailand Economy Series

Format Series Price Ratio Shipping Search Drawing Product Material Table Techinfo Others BD M D GM Format Series Price Ratio Shipping Search Drawing Product Material Table Techinfo Others BD M D GM
KW
Pict
Title
KW
Title
Pict
Date
Date
Name
Name
AK AK
M M
Economy Series Product Overview Product Overview Economy Series
Linear Guides for Medium and Heavy Load Linear Guides for Medium and Heavy Load
· Running Parallelism ·【Running Parallelism】 The values in the table are all measured after the rail is fixed on the
vs Standard Type reference base.When moving the slider within the full length of the rail, measure the change of the
Economy Series Saving Rail Length (mm) Accuracy grade (μm) block upper surface C relative to the slide rail bottom surface A and the change of the block
up to
2 Linear Guides for 77 % 100~200 14 reference surface D relative to the slide rail reference surface B. 2
200~300
15
· Running parallelism of surface D
· Running parallelism of surface C
Linear Guides / Linear Bushings / Ball Splines / Oil Free Bushings Medium and Heavy Load 1100~1500 20 Ball Splines / Oil Free Bushings Linear Guides / Linear Bushings /
against surface B
300~500
17
against surface A
500~700
22
700~900
24
900~1100
26
1500~1900
28
2500~3100
33
Miniature Linear Guides Various range of blocks 1900~2500 31 * The above figure shows machining until the surface A (slide rail mounting surface) is flat, Linear Guides Miniature
Short delivery time
36
3100~3600
3600~3960
37
and the surface B and the surface E (slide rail contact surface) are parallel.
P.309 Interchangeable blocks QAllowable Load The latest availability of lengths over 2m can be confirmed on web product page. P.309
Linear Guides for Medium and Heavy Load · Basic Dynamic Rated Load (C) 3 Medium and Heavy Load Linear Guides for
The basic dynamic rated load is the load that enables a group of identical linear guides to move separately under the same conditions, 90% of which will
not cause material damage due to rolling fatigue, and will slide 50×10 m in a constant direction.
The basic static rated load is the static load required to make the sum of the permanent deformation amount of the rolling element and the permanent
P.321 QStructure and Features · Feature 1: Standard rail mounting holes are equipped with · Basic Static Rated Load (Co) P.321
deformation amount of the rolling surface on the contact part bearing the maximum stress equal to 0.0001 times the diameter of the rolling element.
Cross Roller Guides Block Retainer · Feature 2: The slide rail and the block are in contact with · Static Allowable Torque (MA, MB, MC) Guides Cross Roller
dust covers to prevent dirt from accumulating in the
The static torque load limit under the action of torque load is determined by the basic static rated load Co and the same permanent deformation amount.
mounting holes when the equipment is in use.
Allowable Load (N)≤Co/fS
each other through the rolling ball, so the shaking is small,
P.337 Return Cap · Feature 3: Due to a point-to-surface contact, the frictional M A fS: Static Safety Factor Co: Basic Static Rated Load (N) P.337
Allowable Torque (N·m)≤(MA, MB, MC)/fS
Side Seal
and it is suitable for equipment with precision requirements.
Linear Guide Shafts Rail Under Seal resistance is small, and it can perform subtle movements to M C M A MA, MB, MC: Static allowable torque (N·m) M C Shafts Linear Guide
Ball
achieve device positioning.
M B
the rotating surface is dispersed due to the rolling groove of
P.341 · Feature 4: It has a large allowable load because the force on P.341
the ball. M B
· Feature 5: It is suitable for high speed motion because it is
Linear Bushings not easy to produce friction heat when operating and not Up and down swing direction Left and right swing direction Rolling direction Bushings Linear
easily deformed by heat.
The basic static rated load Co at rest or at low speed shall be
P.349 QPrecision · Static Safety Factor (fS) Table-2 Static Safety Factor (Lower limit of fS) Lower limit of fS P.349
Operating Condition
used after dividing by the static safety factor fs shown in Table-2
Ball Spline · Dimensional Precision Unit: mm ·【Height H Pair Variation】 The difference according to the operating condition. Under normal operating condition 1~2 Ball Spline
2~4
When smooth movement performance is required
between the minimum value and the maximum
In case of vibration and impact
3~5
value of the height (H) dimensions of multiple
Dimensional
P.386 Precision Type Precision Standard 15,20 25,30,35,45 blocks assembled on 1 rail. Alteration P.386
·【Width N Pair Variation】 The difference Alterations 4Code Spec.
between the minimum value and the maximum
Oil Free Bushings Height H Tolerance ±0.1 ±0.1 value of the width of multiple blocks and slide 2-Block Specifications B2 1 block added to 1-block product to ship as 2 block item. Bushings Oil Free
rails assembled on 1 rail.
E If the rail is too short to fit multiple blocks, the blocks will be shipped in a separate package.
Reference side
P.409 Height H Pair 3-Block Specifications B3 2 blocks added to 1-block product to ship as 3 block item. P.409
Shaft Supports Shaft Collars Medium / Heavy Variation 0.02 0.02 3 blocks added to 1-block product to ship as 4 block item. Shaft Collars Shaft Supports
E If the rail is too short to fit multiple blocks, the blocks will be shipped in a separate package.
Linear Guide -
Load Type
0
0
P.430 Width N Tolerance -0.1 -0.1 H 4-Block Specifications B4 E If the rail is too short to fit multiple blocks, the blocks will be shipped in a separate package. P.430
ZA: Light
Preload adjustment Preload Change “No Preload Prodcut” -> “Light Preload Product” or “Medium Preload Product”
Width N Pair 0.02 0.03 ZB: Medium
Preload
Variation
N Left End Cut ES Engraving EB
ES
*There is a difference in accuracy compared to the standard product, but the price Rail Ends Cut Specify the ends cut in 0.5mm increments, and when the specified end cut is larger than or
is more affordable. Right End Cut similar to the holes pitch, the cut may result in broken holes.
EB 322

1BSU @&/ JOEC
1BSU @&/ JOEC