Page 882 - MiSUMi 2025

Cantilever Shafts Screw Mount, Tapped End / Retaining Ring Groove

QTapped End
New Type M Material S Surface Treatment
Products E-FXHB General Structural Steel Black Oxide Film
E-PFXHB or Carbon Steel Electroless Nickel Plating
E-SFXHB SUS304 Equivalent -
E-PHFXHB Tempered steel hardness 30HRC~ Electroless Nickel Plating
E If there are requirements for rust prevention, give priority to products with surface treatment of electroless nickel
plating or those made of stainless steel.
t MA×2 Dimensions of Wrench Flats
M M×1.5 5MA when Y ≥ 17

H 2Dg7

15
+0.1 0
3Y ±0.1 4F 0 W-0.3 Above 17
Part Number 1mm increments 5MA (Coarse Thread) M
1Type 2Dg7 3Y 4F Selectable (Coarse Thread) t H W
6 - 0.004 3 M3 11 10 8
- 0.016
8 - 0.005 5~100 4 M4 12.5 12 10
10 - 0.020 4 5 6 M6 14 15 13
E-FXHB 12 17 14
10 E-PFXHB 13 2~60 5 6 8 M8 17 18 15 10
E-SFXHB 15 - 0.006 10~150 6 8 10 M10 20 20 17
- 0.024
18
21
16
E-PHFXHB*
17
Pivot Pins / Cantilever Shafts *D20 dimension is not available for E-PHFXHB. 4~75 6 8 10 12 M12 25 23 20 Cantilever Shafts Pivot Pins /
18
- 0.007
20
24
26
- 0.028
E Please select Y and F so that t dimension in the drawing is no less than the value shown in the above table. When the pilot hole interferes, it goes through.
Ordering Part Number (1Type · 2D) - 3Y - 4F - 5MA
Example E-FXHB6 - 17 - F25 - MA3
Pivot Pins QRetaining Ring Groove Pivot Pins
M Material
Type
New
Black Oxide Film
P.10-005 Products E-FXHA General Structural Steel or Carbon Steel S Surface Treatment P.10-005
E-PFXHA SUS304 Equivalent Electroless Nickel Plating
E-SFXHA
-
Cantilever Shafts E If there are requirements for rust prevention, give priority to products with surface treatment of electroless nickel Shafts Cantilever
plating or those made of stainless steel.
when Y≥17
P.10-017 M M×1.5 a Dimensions of Wrench Flats P.10-017
Other New Products H m d 2Dg7 15 Products Other New
0
+0.1
Y±0.1
P.10-020 E This type may have centering holes 3 4F 0 n W -0.3 Above 17 P.10-020
depending on dimensions.
Part Number 1mm increments M a H W d m n
1Type 2Dg7 3Y 4F (Coarse Thread) Reference Dimension Tolerance
- 0.004 + 0.075
6 M3 10 8 5 0.7 2
- 0.016 0
8 5~100 M4 12 10 7 + 0.090 0.9
- 0.005 0 3
10 - 0.020 M6 15 13 9.6 0
E-FXHA 2~60 5 -0.090
E-PFXHA 12 M8 17 14 11.5 1.15
18
15
12.4
13
E-SFXHA 15 - 0.006 20 17 14.3 0
16 - 0.024 21 18 15.2 -0.110
17 10~150 M10 16.2 4
18 23 20 17
- 0.007 0 1.35
20 - 0.028 4~75 M12 7 26 24 19 -0.210
E When (M×1.5)+a≥Y+F, the pilot hole for M goes through. When M×1.5≥Y+F, M goes through too.
Ordering Part Number (1Type · 2D) - 3Y - 4F
Example E-FXHA6 - 2 - F5
10-019 Cantilever Shafts 10-020