Page 939 - MiSUMi 2025

2B 3L Motor Selection Conveyors
1Part 7Belt Specification P.11-007
Number 10mm 5mm 4Output 5Specification 6Gearhead (Not specified: material is PU) 8Motor
increments increments (W) Reduction Ratio
SCM 5 7.5 10 12.5 15 18 H G Flat Belts Flat Belt Pulleys /
(Single-phase 220V 25 30 36 50 60 75 (General Purpose·White,
6 (GPG
25 Variable Speed Motor) 90 100 120 150 180 Tooth Surface Cloth Lined) Motor)
S
INV Note: 5~10 not (For Sliding·Green, J P.11-071
(3-Phase 220V
E-CVGTA 80~300 255~2000 Note: 6 not Induction Motor) applicable for 6W Both Sides Cloth Lined) (JSCC
Motor)
applicable
for Motor D Guide Rollers Urethane Molded Bearings / Urethane Molded Rollers /
(Antistatic·Black,
Induction Both Sides Cloth Lined) R
Motor NM NH (No Motor,
(No Motor) (No Gearhead) J
(No Belt) Gearhead) P.11-085
EIf a stepper motor or servo motor is required for automatic control, the type with no motor and gearhead can be selected.
EWhen "No motor, gearhead" is selected, the motor mounting hole pitch will vary depending on the motor's power rating.
E When "No motor, gearhead" is selected, the main unit will be delivered unassembled. The customer should assemble the main unit by Cam Followers Ball Rollers /
following instructions on the included assembly procedure manual.
Ordering 1Part Motor Selection 7Belt P.11-097
Example Number - 2B - 3L - 4Output - 5Specification - 6Gearhead Reduction Ratio - Specification - 8Motor
E-CVGTA - 100 - 1000 - 6 - SCM - 25 - H - G
For No Belt E-CVGTA - 100 - 1000 - 25 - SCM - 30 - J - G with Screw / Roller Carriers Silicon Bearings / Bearings
For No Motor, E-CVGTA - 100 - 1000 - 25 - NM - NH - H - R
Gearhead
P.11-119
Ordering 1Part Motor Selection 7Belt
Alterations Example Number - 2B - 3L - 4Output - 5Specification - 6Gearhead Reduction Ratio - Specification - 8Motor - Alteration
E-CVGTA - 100 - 1000 - 6 - SCM - 25 - H - G - MK Placon Rollers / Free Rollers /
Alterations Code Spec. Sprocket Rollers
Motor Position Reversed P.11-125
Motor
Transfer Direction The motor position can be changed. 11
MK Ordering Code MK
Can only be designated for the head drive type.
Motor
Mounting Bracket for Speed Controller Rollers / Cam Followers Conveyors / Flat Belts /
Mounting bracket for speed controller is
SCB included.
Ordering Code SCB

QConveying Capacity QGearhead Reduction Ratio - Speed Correspondence Table
E May decrease depending on load condition. *Reference value
Timing Belt Speed (m/min)
Gearhead
Reduction Ratio SCM Variable Speed INV Induction Motor
Motor
Transfer Weight (Unit/Kg) 12.5 21.7~36.2 45.0
5
67.5
32.6~54.3
7.5
16.3~27.1
10
33.8
27.0
13.0~21.7
10.9~18.1
22.5
15
18
6.5~10.9
13.5
25
11.3
30 9.0~15.1 18.8
5.4~9.0
36 4.5~7.5 9.4
50 3.3~5.4 6.8
Timing Belt Speed (m/min) 60 2.7~4.5 5.6
E This graph shows conveying capacity 75 2.2~3.6 4.5
with horizontal conditions.
E Conveying capacity varies depending on 90 1.8~3.0 3.8
usage conditions. 100 1.6~2.7 3.4
E When a variable speed motor is selected, 120 1.4~2.3 2.8
the conveying capacity will not increase 150 1.1~1.8 2.3
as the speed decreases. 180 0.9~1.5 1.9
11-055 Conveyors 11-056