Page 937 - MiSUMi 2025

QDetails of A Dimension QBelt Width - Pulley Center Distance Correspondence Table Conveyors
Belt
Motor Motor Reduction A Model Width Pulley Center Distance L P.11-007
Power Specifications Manufacturer Ratio B L330~400 L405~500 L505~600 L605~900 L905~2000
3~18 L107 10 I I I I I
Variable GPG 25~180 L117 E-CVSTR 20 I I I I I
6W Speed Flat Belts Flat Belt Pulleys /
Motor JSCC 3~18 L118
25~180 L130
P.11-071
1Part 2B 3L Motor Selection 7Belt Specification
Number Selection 5mm 4Output 5Specification 6Gearhead (Not specified: material is PU) 8Motor
increments (W) Reduction Ratio Guide Rollers Urethane Molded Bearings / Urethane Molded Rollers /
SCM 12.5 15 18 H (General Purpose·White, G (GPG Motor)
(Single-phase 220V 25 30 36 50 60 75 Tooth Surface Cloth Lined) J (JSCC P.11-085
S (For Sliding·Green,
E-CVSTR 10 330~2000 6 Variable Speed Motor) 90 100 120 150 180 Both Sides Cloth Lined) Motor)
20
NM NH D (Antistatic·Black, R (No Motor,
(No Motor) (No Gearhead) Both Sides Cloth Lined) Gearhead) Cam Followers Ball Rollers /
J (No Belt)
EIf a stepper motor or servo motor is required for automatic control, the type with no motor and gearhead can be selected.
EWhen "No motor, gearhead" is selected, the motor mounting hole pitch will vary depending on the motor's power rating. P.11-097
E When "No motor, gearhead" is selected, the main unit will be delivered unassembled. The customer should assemble the main unit by
following instructions on the included assembly procedure manual.
Ordering 1Part Motor Selection 7Belt with Screw / Roller Carriers Silicon Bearings / Bearings
Example Number - 2B - 3L - 4Output - 5Specification - 6Gearhead Reduction Ratio - Specification - 8Motor
E-CVSTR - 10 - 1000 - 6 - SCM - 25 - H - G P.11-119
For No Belt E-CVSTR - 10 - 1000 - 6 - SCM - 30 - J - G
For No Motor, E-CVSTR - 10 - 1000 - 6 - NM - NH - H - R
Gearhead Sprocket Rollers Placon Rollers / Free Rollers /
Ordering 1Part Motor Selection 7Belt
Alterations Example Number - 2B - 3L - 4Output - 5Specification - 6Gearhead Reduction Ratio - Specification - 8Motor - Alteration
E-CVSTR - 10 - 1000 - 6 - SCM - 25 - H - G - MP200 P.11-125
Alterations Code Spec. 11
Specified Drive Section Position Transfer Direction
The drive section position can be changed.
MP Ordering Code MP200 180≤MP≤L-250
*Minimum value of L is 435 Rollers / Cam Followers Conveyors / Flat Belts /
Can only be specified for the center drive type.
MP
Mounting Bracket for Speed Controller
Mounting bracket for speed controller is
SCB included.
Ordering Code SCB

QConveying Capacity QGearhead Reduction Ratio - Speed Correspondence Table
E May decrease depending on load condition. *Reference value
Gearhead Reduction Ratio Timing Belt Speed (m/min)
Transfer Weight (Unit/Kg) 18 4.5~7.5
6.5~10.9
12.5
5.4~9.0
15
3.3~5.4
25
2.7~4.5
30
2.3~3.8
36
50
60
1.4~2.3
75 1.6~2.7
1.1~1.8
Timing Belt Speed (m/min) 90 0.9~1.5
E This graph shows conveying capacity 100 0.8~1.4
with horizontal conditions. 120 0.7~1.1
E Conveying capacity varies depending on 150 0.5~0.9
usage conditions. 180 0.5~0.8
E When a variable speed motor is selected,
the conveying capacity will not increase
as the speed decreases during use.
11-053 Conveyors 11-054