Page 933 - MiSUMi 2025

3L Motor Selection Conveyors
1Part 2B 7Belt Specification P.11-007
Number Selection 5mm 4Output 5Specification 6Gearhead (Not specified: material is PU) 8Motor
increments (W) Reduction Ratio
H9 (General Purpose·Green) G
SCM W9 (General Purpose·White) Flat Belts Flat Belt Pulleys /
12.5 15 18 25 30
(Single-phase 220V 36 50 60 7590 100 U5 (For Sliding·Green) (GPG Motor)
J
Variable Speed 120 150 180 S5 (For Sliding·White) (JSCC
E-CVSMA 60 Motor) D9 (Antistatic·Black) Motor) P.11-071
(Crowned 100 415~2000 6 F12 (For Food Transfer·White)
Roller) 150 O14 (Oil Resistant·Green)
NM NH Q10 (For Inclined Transfer·Green) R Guide Rollers Urethane Molded Bearings / Urethane Molded Rollers /
(No Motor) (No Gearhead) Y12 (General Purpose·Yellow PVC) (No Motor,
V12 (General Purpose·Red PVC) Gearhead)
J (No Belt) P.11-085
EBelt thickness is a nominal value and the actual thickness is one-tenth of the nominal value, measured in millimeters, except for D9.
E The oil-resistant specification applies only to the conveying surface. If oil comes into contact with the back side of the belt, it may
become unusable. Cam Followers Ball Rollers /
EIf a stepper motor or servo motor is required for automatic control, the type with no motor and gearhead can be selected.
EWhen "No motor, gearhead" is selected, the motor mounting hole pitch will vary depending on the motor's power rating.
E When "No motor, gearhead" is selected, the main unit will be delivered unassembled. The customer should assemble the main unit by P.11-097
following instructions on the included assembly procedure manual.
Ordering 1Part Motor Selection 7Belt with Screw / Roller Carriers Silicon Bearings / Bearings
Example Number - 2B - 3L - 4Output - 5Specification - 6Gearhead Reduction Ratio - Specification - 8Motor
E-CVSMA - 100 - 1000 - 6 - SCM - 25 - H9 - G
For No Belt E-CVSMA - 100 - 1000 - 6 - SCM - 30 - J - G P.11-119
For No Motor, E-CVSMA - 100 - 1000 - 6 - NM - NH - H9 - R
Gearhead
Ordering 1Part Motor Selection 7Belt Sprocket Rollers Placon Rollers / Free Rollers /
Alterations Example Number - 2B - 3L - 4Output - 5Specification - 6Gearhead Reduction Ratio - Specification - 8Motor - Alteration
E-CVSMA - 100 - 1000 - 6 - SCM - 25 - H9 - G - SCB
P.11-125
Alterations Code Spec. 11
Mounting Bracket for Speed Controller
Mounting bracket for speed controller is
SCB included.
Ordering Code SCB Rollers / Cam Followers Conveyors / Flat Belts /

QConveying Capacity QGearhead Reduction Ratio - Speed Correspondence Table
E May decrease depending on load condition. *Reference value
Gearhead Flat Belt Speed (m/min)
Reduction Ratio SCM Variable Speed Motor
Transfer Weight (Unit/Kg) 18 9.9~16.5
12.5
14.2~23.7
15
11.9~19.8
7.1~11.9
25
5.9~9.9
30
36
4.9~8.2
50
3.0~4.9
60
2.4~4.0
75 3.6~5.9
90 2.0~3.3
100 1.8~3.0
120 1.5~2.5
Flat Belt Speed (m/min) 150
E This graph shows conveying capacity 180 1.2~2.0
1.0~1.6
with horizontal conditions.
E Conveying capacity varies depending on
usage conditions.
E When a variable speed motor is selected,
the conveying capacity will not increase
as the speed decreases.
11-049 Conveyors 11-050