Page 931 - MiSUMi 2025

1Part 2W 3L 4E 5F Motor Selection 9Belt Light P.11-007
Conveyors
Number Selection 5mm Luminous Luminous 6Output 7Specification 8Gearhead Specification Motor Color
increments Area Position Area Length (W) Reduction Ratio
50
SCM
50 100 (Single- H Flat Belts Flat Belt Pulleys /
100 phase 220V 5 7.5 10 G (White)
(GPG
100 150 Variable 12.5 15 18 Motor) R
200 25 Speed Motor) 25 30 36 K9 (Red) P.11-071
G
E-CVBTN 150 250 40 50 60 75 90 (Translucent J (Green)
(Crowned 540~3000 80~2500 60 INV 100 120 150 Belt, White) (JSCC U
Roller) 200 200 (3-Phase 220V 180 Motor) Guide Rollers Urethane Molded Bearings / Urethane Molded Rollers /
250 90 Induction Motor) J (No Belt) (Blue)
250 W
250 (Infrared)
300 NM NH R Z P.11-085
300 300 (No Motor) (No (No Motor, (Ultraviolet)
400 Gearhead) Gearhead)
EBelt thickness is a nominal value and the actual thickness is one-tenth of the nominal value, measured in millimeters, except for D9. Cam Followers Ball Rollers /
EIf a stepper motor or servo motor is required for automatic control, the type with no motor and gearhead can be selected.
EWhen "No motor, gearhead" is selected, the motor mounting hole pitch will vary depending on the motor's power rating.
E When "No motor, gearhead" is selected, the main unit will be delivered unassembled. The customer should assemble the main unit by P.11-097
following instructions on the included assembly procedure manual.
EFor products with a total length from 2.8m, the delivery time may be longer.
Ordering 1Part - 2W - 3L - 4E - 5F - Motor Selection - 9Belt - Motor - Light with Screw / Roller Carriers Silicon Bearings / Bearings
Example Number 6Output - 7Specification - 8Gearhead Reduction Ratio Specification Color
E-CVBTN - 100 - 1000 - 90 - 100 - 25 - SCM - 25 - K9 - G - H P.11-119
For No Belt E-CVBTN - 100 - 1000 - 90 - 100 - 25 - INV - 25 - J - G - H
For No Motor, E-CVBTN - 100 - 1000 - 90 - 100 - 25 - NM - NH - K9 - R - H
Gearhead
Ordering 1Part Motor Selection 9Belt Light Sprocket Rollers Placon Rollers / Free Rollers /
Alterations Example Number - 2W - 3L - 4E - 5F - 6Output - 7Specification - 8Gearhead Reduction Ratio - Specification - Motor - Color - Alteration
E-CVBTN - 100 - 1000 - 90 - 100 - 25 - SCM - 25 - K9 - G - H - MP240 P.11-125
Alterations Code Spec. 11
Specified Drive Section Position Transfer Direction
The drive section position can be changed.
MP Ordering Code MP240 180≤MP≤L-400
*Minimum value of L is 580
Can only be specified for the center drive type. Rollers / Cam Followers Conveyors / Flat Belts /
MP
Mounting Bracket for Speed Controller
Mounting bracket for speed controller is
SCB included.
Ordering Code SCB
QConveying Capacity QGearhead Reduction Ratio - Speed Correspondence Table
E May decrease depending on load condition. *Reference value
Flat Belt Speed (m/min)
Gearhead
Reduction Ratio SCM Variable Speed INV Induction Motor
Motor
Transfer Weight (Unit/Kg) 12.5 17.0~28.3 35.2
52.8
5
25.4~42.4
7.5
10
26.4
12.7~21.2
21.1
10.2~17.0
17.6
15
8.5~14.1
18
7.1~11.8
14.7
10.6
5.1~8.5
25
30
3.5~5.9
7.3
36
5.3
2.5~4.2
50 4.2~7.1 8.8
60 2.1~3.5 4.4
75 1.7~2.8 3.5
Flat Belt Speed (m/min) 90 1.4~2.4 2.9
E This graph shows conveying capacity 100 1.3~2.1 2.6
1.1~1.8
2.2
120
with horizontal conditions.
E Conveying capacity varies depending on 150 0.8~1.4 1.8
usage conditions. 180 0.7~1.2 1.5
E When a variable speed motor is selected,
the conveying capacity will not increase
as the speed decreases.
11-047 Conveyors 11-048