Page 941 - MiSUMi 2025

2B 3L Motor Selection Conveyors
1Part 7Belt Specification P.11-007
Number 10mm 5mm 4Output 5Specification 6Gearhead (Not specified: material is PU) 8Motor
increments increments (W) Reduction Ratio
SCM 5 7.5 10 12.5 15 18 H G Flat Belts
(Single-phase 220V 25 30 36 50 60 75 (General Purpose·White, Flat Belt Pulleys /
6 (GPG
25 Variable Speed Motor) 90 100 120 150 180 Tooth Surface Cloth Lined) Motor)
S
INV Note: 5~10 not (For Sliding·Green, J P.11-071
(3-Phase 220V
E-CVGTN 80~300 365~2000 Note: 6 not Induction Motor) applicable for 6W Both Sides Cloth Lined) (JSCC
Motor)
applicable
for Motor D Guide Rollers Urethane Molded Bearings / Urethane Molded Rollers /
(Antistatic·Black,
Induction Both Sides Cloth Lined) R
Motor NM NH (No Motor,
(No Motor) (No Gearhead) J
(No Belt) Gearhead) P.11-085
EIf a stepper motor or servo motor is required for automatic control, the type with no motor and gearhead can be selected.
EWhen "No motor, gearhead" is selected, the motor mounting hole pitch will vary depending on the motor's power rating.
E When "No motor, gearhead" is selected, the main unit will be delivered unassembled. The customer should assemble the main unit by Cam Followers Ball Rollers /
following instructions on the included assembly procedure manual.
P.11-097
Ordering 1Part Motor Selection 7Belt
Example Number - 2B - 3L - 4Output - 5Specification - 6Gearhead Reduction Ratio - Specification - 8Motor
E-CVGTN - 120 - 1000 - 6 - SCM - 25 - H - G
For No Belt E-CVGTN - 120 - 1000 - 25 - SCM - 30 - J - G with Screw / Roller Carriers Silicon Bearings / Bearings
For No Motor, E-CVGTN - 120 - 1000 - 25 - NM - NH - H - R
Gearhead
P.11-119
Ordering 1Part Motor Selection 8Belt
Alterations Example Number - 2B - 3L - 4Output - 5Voltage - 6Specification - 7Gearhead Reduction Ratio - Specification - 9Motor - Alteration
E-CVGTN - 120 - 1000 - 6 - TA220 - SCM - 25 - H - G - MP200 Sprocket Rollers Placon Rollers / Free Rollers /
Alterations Code Spec.
Specify Drive Section Position Transfer Direction P.11-125
The drive section position can be changed. 11
MP Ordering Code MP200 170≤MP≤L-330
*Minimum value of L is 500
Can only be specified for the center drive type.
MP
Mounting Bracket for Speed Controller Rollers / Cam Followers Conveyors / Flat Belts /
Mounting bracket for speed controller is
SCB included.
Ordering Code SCB

QConveying Capacity QGearhead Reduction Ratio - Speed Correspondence Table
E May decrease depending on load condition. *Reference value
Timing Belt Speed (m/min)
Gearhead
Reduction Ratio SCM Variable Speed INV Induction Motor
Motor
Transfer Weight (Unit/Kg) 12.5 17.0~28.3 35.2
5
25.4~42.4
52.8
7.5
12.7~21.2
10
26.4
21.1
10.2~17.0
15
8.5~14.1
17.6
18
10.6
5.1~8.5
25
4.2~7.1
8.8
30 7.1~11.8 14.7
36 3.5~5.9 7.3
50 2.5~4.2 5.3
Timing Belt Speed (m/min) 60 2.1~3.5 4.4
E This graph shows conveying capacity 75 1.7~2.8 3.5
with horizontal conditions. 90 1.4~2.4 2.9
E Conveying capacity varies depending on
usage conditions. 100 1.3~2.1 2.6
E When a variable speed motor is selected, 120 1.1~1.8 2.2
the conveying capacity will not increase 150 0.8~1.4 1.8
as the speed decreases. 180 0.7~1.2 1.5
11-057 Conveyors 11-058