Page 945 - MiSUMi 2025

2B 3L Motor Selection Conveyors
1Part 7Belt Specification P.11-007
Number 10mm 5mm 4Output 5Specification 6Gearhead (Not specified: material is PU) 8Motor
increments increments (W) Reduction Ratio
SCM H Flat Belts Flat Belt Pulleys /
(Single-phase 220V (General Purpose·White, G
Variable Speed Motor) 5 7.5 10 12.5 15 18 Tooth Surface Cloth Lined) (GPG Motor)
25 30 36 50 60 75 S J
INV 90 100 120 150 180 (For Sliding·Green, (JSCC P.11-071
(3-Phase 220V
E-CVGTP 80~300 365~3000 25 Induction Motor) Both Sides Cloth Lined) Motor)
40
D
(Antistatic·Black, Guide Rollers Urethane Molded Bearings / Urethane Molded Rollers /
NM NH Both Sides Cloth Lined) R
(No Motor) (No Gearhead) J (No Motor,
(No Belt) Gearhead) P.11-085
EIf a stepper motor or servo motor is required for automatic control, the type with no motor and gearhead can be selected.
EWhen "No motor, gearhead" is selected, the motor mounting hole pitch will vary depending on the motor's power rating.
E When "No motor, gearhead" is selected, the main unit will be delivered unassembled. The customer should assemble the main unit by Cam Followers Ball Rollers /
following instructions on the included assembly procedure manual.
EFor products with a total length from 2.8m, the delivery time may be longer.
P.11-097
Ordering 1Part Motor Selection 7Belt
Example Number - 2B - 3L - 4Output - 5Specification - 6Gearhead Reduction Ratio - Specification - 8Motor
E-CVGTP - 100 - 1000 - 25 - SCM - 25 - H - G with Screw / Roller Carriers Silicon Bearings / Bearings
For No Belt E-CVGTP - 100 - 1000 - 25 - INV - 30 - J - G
For No Motor, E-CVGTP - 100 - 1000 - 25 - NM - NH - H - R
Gearhead
P.11-119
Ordering 1Part Motor Selection 7Belt
Alterations Example Number - 2B - 3L - 4Output - 5Specification - 6Gearhead Reduction Ratio - Specification - 8Motor - Alteration
E-CVGTP - 100 - 1000 - 25 - SCM - 25 - H - G - MP200 Sprocket Rollers Placon Rollers / Free Rollers /
Alterations Code Spec.
Specified Drive Section Position Transfer Direction P.11-125
The drive section position can be changed. 11
MP Ordering Code MP200 175≤MP≤L-380
*Minimum value of L is 555
Can only be specified for the center drive type.
MP
Mounting Bracket for Speed Controller Rollers / Cam Followers Conveyors / Flat Belts /
Mounting bracket for speed controller is
SCB included.
Ordering Code SCB

QConveying Capacity QGearhead Reduction Ratio - Speed Correspondence Table
E May decrease depending on load condition. *Reference value
Timing Belt Speed (m/min)
Gearhead
Reduction Ratio SCM Variable Speed INV Induction Motor
Motor
Transfer Weight (Unit/Kg) 12.5 19.3~32.2 40.1
5
29.0~48.3
60.1
7.5
10
14.5~24.2
30.1
11.6~19.3
24.1
15
20.0
9.7~16.1
18
5.8~9.7
12.0
25
30 8.1~13.4 16.7
10.0
4.8~8.1
36 4.0~6.7 8.4
50 2.9~4.8 6.0
60 2.4~4.0 5.0
Timing Belt Speed (m/min) 75 1.9~3.2 4.0
E This graph shows conveying capacity 90 1.6~2.7 3.3
with horizontal conditions.
E Conveying capacity varies depending on 100 1.4~2.4 3.0
usage conditions. 120 1.2~2.0 2.5
E When a variable speed motor is selected, 150 1.0~1.6 2.0
the conveying capacity will not increase 180 0.8~1.3 1.7
as the speed decreases.
11-061 Conveyors 11-062