Page 780 - MiSUMi 2025

Economy series Product Overview Product Overview Economy series
Bearings Bearings

QFeatures of MISUMI Economy series Bearings
Economy series New 1Why are all MISUMI Economy series Bearings tested for noise and vibration? And why do we insist on achieving "Z1" level?
Specs
Bearings Through the test of Bearing noise and vibration, we can find out whether the Bearing is defective. Bearing
vibration is divided into four levels: Z0, Z1, Z2, Z3 and Z4 (Higher level, Lower noise and vibration)
Noise and vibration specifications Noise and vibration specifications
Applications of Economy series Bearings Dimension Tolerance of of generic products on the market * of MISUMI Economy series
I.D. and O.D., etc.
Low load: Bearings for transporting light workpieces Clearance Tolerance
Can
9 Medium and low speed rotation: Bearings suitable for Roundness of Bearing Ball Cannot guarantee
medium and low speed transferring equipment
Z1
guarantee
Bearings / Bearings with Housings / Related Accessories Medium precision rotation: Bearings that Ring and Outer Ring higher
level or
Z1 level
Rail Accuracy of Bearing Inner
do not require precise positioning
Scratches inside the Bearing,
and foreign matters mixed in
QExample of Use
Bearings 2Why do we insist on using "standard wall thickness" for MISUMI Economy series Bearings?

QMISUMI Economy series Bearings: Wall thickness of generic products on the market* Standard wall thickness for MISUMI Economy series
P.09-007 Low Load Medium and Low Speed Rotation Medium Precision Rotation
Bearings with Housings QThe recommended areas of use are as follows: Steel Ball The ballistic Steel Ball Deep Rail The ballistic
……It is suitable for such applications
contact surface is
contact area is
large, and the
reduced and the
P.09-038 1Low load: Bearings for transporting light workpieces Workpiece Transfer Shallow Rail contact stress is contact stress is
Application
relatively
relatively
2Medium and low speed rotation: Bearings suitable for Workpiece Transfer Thinner Wall Thickness concentrated, Standard Wall Thickness dispersed, thus
Bearing Lock Nuts medium and low speed transferring equipment Application Bearing thus affecting the Bearing prolonging the
service life.
service life.
3Medium precision rotation: Bearings that do not require
Inner Ring
Inner Ring
precise positioning
P.09-081
Bearing Shaft Screws / Bearing Spacers 3Why do we insist on using "bearing steel" and "stainless steel" materials with excellent
performance for MISUMI Economy series Bearings?
P.09-086 QPrecautions of Selection Material and difference for generic Material and difference for
Other New Products (Bearing Related) · Differences in specifications between MISUMI Standard product Bearings (B6901ZZ) and MISUMI Normal steel on the market SUJ2 (Bearing Steel)
products on the market*
MISUMI Economy series
Heat Treatment Hardness
Heat Treatment Hardness
P.09-090 Economy series Bearings (C-E6901ZZ) 48~54HRC Not abrasion 58~63HRC More abrasion
resistant
resistant
MISUMI Standard product Bearings MISUMI Economy series Bearings Bearing Steel Product
QResult After Test QResult After Test
After service life test under After the long-term service life
Basic Dynamic Rated Load (Cr): 2.89kN Basic Dynamic Rated Load (Cr): 2kN
Basic Load Capacity the same conditions as test, there was little wear inside
Basic Static Rated Load (Cor): 1.46kN Basic Static Rated Load (Cor): 1kN MISUMI Economy series, the open end cover was the open end cover and the structure remains intact.
Basic Rated Life ▲ 1 million rotations Basic Rated Life ▲ 400,000 rotations severely worn inside and the structure was damaged.
(With 2.89kN load applied) (With 2kN load applied)
Lifetime Normal stainless steel on the Equivalent to SUS440 or SUS420
EX: Specific example ▲ 4000 hours EX: Specific example 1600 hours Stainless Steel Product market After the salt spray test, the rusted
▲
(When rotating at speed of 750rpm and load of 0.5kN) (When rotating at speed of 750rpm and load of 0.5kN) After the salt spray test, the area was about 2~3%
rusted area was about 30%
Bearing Internal
Clearance Minimum: 3μm Maximum: 13μm Minimum: 6μm Maximum: 23μm * Generic products on the market are similar products randomly purchased by MISUMI from the market
* The test data are obtained through testing by MISUMI, which are for reference only
09-007