Page 905 - MiSUMi 2025

3L Motor Selection Conveyors
7Belt Specification
2B
1Part Number Selection 5mm 4Output 6Gearhead (Not specified: material is PU) 8Motor P.11-007
increments (W) 5Specification Reduction Ratio
SCM 5 7.5 10 12.5 15 18 H9 (General Purpose·Green) G Flat Belts Flat Belt Pulleys /
E-SVKN 6 (Variable Speed 25 30 36 50 60 75 W9 (General Purpose·White) (GPG
(Crowned Roller) 25 Motor) 90 100 120 150 180 U5 (For Sliding·Green) Motor)
50 40 S5 (For Sliding·White) J P.11-071
Note: 5~10 not
D9 (Antistatic·Black)
INV
E-SVKR 100 300~3000 Note: 6 not (Induction Motor) applicable for 6W F12 (For Food Transfer·White) (JSCC
150
(With 200 applicable Motor O14 (Oil Resistant·Green) Motor)
Meandering 250 for Q10 (For Inclined Transfer·Green) Guide Rollers Urethane Molded Bearings / Urethane Molded Rollers /
Prevention Induction NM NH Y12 (General Purpose·Yellow PVC) R
Crosspieces) Motor (No Motor) (No Gearhead) V12 (General Purpose·Red PVC) (No Motor,
J (No Belt) Gearhead) P.11-085
EBelt thickness is a nominal value and the actual thickness is one-tenth of the nominal value, measured in millimeters, except for D9.
EThe oil-resistant specification applies only to the conveying surface. If oil comes into contact with the back side of the belt, it may become unusable. Cam Followers Ball Rollers /
EIf a stepper motor or servo motor is required for automatic control, the type with no motor and gearhead can be selected.
EWhen "No motor, gearhead" is selected, the motor mounting hole pitch will vary depending on the motor's power rating.
E When "No motor, gearhead" is selected, the main unit will be delivered unassembled. The customer should assemble the main unit by P.11-097
following instructions on the included assembly procedure manual.
EFor products with a total length from 2.8m, the delivery time may be longer.
Ordering 1Part Motor Selection 7Belt with Screw / Roller Carriers Silicon Bearings / Bearings
Example Number - 2B - 3L - 4Output - 5Specification - 6Gearhead Reduction Ratio - Specification - 8Motor
E-SVKR - 150 - 1000 - 25 - SCM - 25 - H9 - G
For No Belt E-SVKR - 150 - 1000 - 25 - INV - 25 - J - G P.11-119
For No Motor, E-SVKR - 150 - 1000 - 25 - NM - NH - H9 - R
Gearhead
Ordering 1Part Motor Selection 7Belt 8 Placon Rollers / Free Rollers /
Alterations Example Number - 2B - 3L - 4Output - 5Specification - 6Gearhead Reduction Ratio - Specification - Motor - Alteration Sprocket Rollers
E-SVKN - 150 - 1000 - 25 - SCM - 25 - H9 - G - MP200
Alterations Code Spec. P.11-125
Specify Drive Section Position Transfer Direction 11
The drive section position can be changed.
MP Ordering Code MP200 150≤MP≤L-370
*Minimum value of L is 520
Can only be specified for the center drive type.
MP Rollers / Cam Followers Conveyors / Flat Belts /
Mounting Bracket for Speed Controller
Mounting bracket for speed controller is
SCB included.
Ordering Code SCB
QConveying Capacity QGearhead Reduction Ratio - Speed Correspondence Table
E May decrease depending on load condition. *Reference value
Gearhead Flat Belt Speed (m/min)
Reduction Ratio SCM Variable Speed INV Induction Motor
Transfer Weight (Unit/Kg) 12.5 17.0~28.3 35.2
Motor
52.8
5
25.4~42.4
7.5
26.4
12.7~21.2
10
21.1
10.2~17.0
15
8.5~14.1
17.6
18
10.6
5.1~8.5
25
4.2~7.1
8.8
30 7.1~11.8 14.7
36 3.5~5.9 7.3
50 2.5~4.2 5.3
Flat Belt Speed (m/min) 60 2.1~3.5 4.4
E This graph shows conveying capacity 75 1.7~2.8 3.5
with horizontal conditions. 90 1.4~2.4 2.9
E Conveying capacity varies depending on 100 1.3~2.1 2.6
usage conditions.
E When a variable speed motor is selected, 120 1.1~1.8 2.2
the conveying capacity will not increase 150 0.8~1.4 1.8
as the speed decreases. 180 0.7~1.2 1.5
11-021 Conveyors 11-022