Page 909 - MiSUMi 2025

2B 3L Motor Selection Conveyors
7Belt Specification
1Part Number 10mm 5mm 4Output 6Gearhead (Not specified: material is PU) 8Motor P.11-007
increments increments (W) 5Specification Reduction Ratio
SCM 5 7.5 10 12.5 15 18 H9 (General Purpose·Green) G Flat Belts Flat Belt Pulleys /
E-CVGN 6 (Single-phase 220V 25 30 36 50 60 75 W9 (General Purpose·White) (GPG
(Crowned Roller) 25 Variable Speed Motor) 90 100 120 150 180 U5 (For Sliding·Green) Motor)
40 INV S5 (For Sliding·White) J P.11-071
Note: 5~10 not
D9 (Antistatic·Black)
E-CVGP 50~300 355~2000 Note: 6 not (3-Phase 220V applicable for 6W F12 (For Food Transfer·White) (JSCC
(With applicable Induction Motor) Motor O14 (Oil Resistant·Green) Motor)
Meandering for Q10 (For Inclined Transfer·Green) Guide Rollers Urethane Molded Bearings / Urethane Molded Rollers /
Prevention Induction NM NH Y12 (General Purpose·Yellow PVC) R
Crosspieces) Motor (No Motor) (No Gearhead) V12 (General Purpose·Red PVC) (No Motor,
J (No Belt) Gearhead) P.11-085
EBelt thickness is a nominal value and the actual thickness is one-tenth of the nominal value, measured in millimeters, except for D9.
EThe oil-resistant specification applies only to the conveying surface. If oil comes into contact with the back side of the belt, it may become unusable. Cam Followers Ball Rollers /
EIf a stepper motor or servo motor is required for automatic control, the type with no motor and gearhead can be selected.
EWhen "No motor, gearhead" is selected, the motor mounting hole pitch will vary depending on the motor's power rating.
E When "No motor, gearhead" is selected, the main unit will be delivered unassembled. The customer should assemble the main unit by P.11-097
following instructions on the included assembly procedure manual.
Ordering 1Part Motor Selection 7Belt
Example Number - 2B - 3L - 4Output - 5Specification - 6Gearhead Reduction Ratio - Specification - 8Motor with Screw / Roller Carriers Silicon Bearings / Bearings
E-CVGN - 200 - 1000 - 25 - SCM - 25 - H9 - G
For No Belt E-CVGN - 200 - 1000 - 25 - INV - 25 - J - G
For No Motor, E-CVGN - 200 - 1000 - 25 - NM - NH - H9 - R P.11-119
Gearhead
Ordering 1Part Motor Selection 7Belt 8
Alterations Example Number - 2B - 3L - 4Output - 5Specification - 6Gearhead Reduction Ratio - Specification - Motor - Alteration Sprocket Rollers Placon Rollers / Free Rollers /
E-CVGN - 200 - 1000 - 25 - SCM - 25 - H9 - G - MP200
Alterations Code Spec.
Specify Drive Section Position Transfer Direction P.11-125
11
The drive section position can be changed.
MP Ordering Code MP200 155≤MP≤L-375
*Minimum value of L is 530
Can only be specified for the center drive type.
MP Rollers / Cam Followers Conveyors / Flat Belts /
Mounting Bracket for Speed Controller
Mounting bracket for speed controller is
SCB included.
Ordering Code SCB

QConveying Capacity QGearhead Reduction Ratio - Speed Correspondence Table
E May decrease depending on load condition. *Reference value
Flat Belt Speed (m/min)
Gearhead SCM Variable Speed INV Induction Motor
Reduction Ratio
Transfer Weight (Unit/Kg) 12.5 17.0~28.3 35.2
Motor
5
25.4~42.4
52.8
7.5
12.7~21.2
10
26.4
21.1
10.2~17.0
17.6
15
8.5~14.1
18
5.1~8.5
10.6
25
30 7.1~11.8 14.7
4.2~7.1
8.8
36 3.5~5.9 7.3
50 2.5~4.2 5.3
Flat Belt Speed (m/min) 60 2.1~3.5 4.4
E This graph shows conveying capacity 75 1.7~2.8 3.5
with horizontal conditions. 90 1.4~2.4 2.9
E Conveying capacity varies depending on
usage conditions. 100 1.3~2.1 2.6
E When a variable speed motor is selected, 120 1.1~1.8 2.2
the conveying capacity will not increase 150 0.8~1.4 1.8
as the speed decreases. 180 0.7~1.2 1.5
11-025 Conveyors 11-026