Page 911 - MiSUMi 2025

2B 3L Motor Selection Conveyors
7Belt Specification
1Part Number 10mm 5mm 4Output 6Gearhead (Not specified: material is PU) 8Motor P.11-007
increments increments (W) 5Specification Reduction Ratio
SCM 5 7.5 10 12.5 15 18 H9 (General Purpose·Green) G Flat Belts
6 (Single-phase 220V 25 30 36 50 60 75 W9 (General Purpose·White) Flat Belt Pulleys /
(GPG
25 Variable Speed Motor) 90 100 120 150 180 U5 (For Sliding·Green) Motor)
E-CVSJA 40 S5 (For Sliding·White) J P.11-071
(With INV Note: 5~10 not D9 (Antistatic·Black) (JSCC
Meandering 50~300 220~600 Note: 6 not (3-Phase 220V applicable for 6W F12 (For Food Transfer·White) Motor)
Prevention applicable Induction Motor) Motor O14 (Oil Resistant·Green)
Crosspieces) for Q10 (For Inclined Transfer·Green) Guide Rollers Urethane Molded Bearings / Urethane Molded Rollers /
Induction NM NH Y12 (General Purpose·Yellow PVC) R
Motor (No Motor) (No Gearhead) V12 (General Purpose·Red PVC) (No Motor,
J (No Belt) Gearhead) P.11-085
EBelt thickness is a nominal value and the actual thickness is one-tenth of the nominal value, measured in millimeters, except for D9.
EThe oil-resistant specification applies only to the conveying surface. If oil comes into contact with the back side of the belt, it may become unusable.
EIf a stepper motor or servo motor is required for automatic control, the type with no motor and gearhead can be selected. Cam Followers Ball Rollers /
EWhen "No motor, gearhead" is selected, the motor mounting hole pitch will vary depending on the motor's power rating.
E When "No motor, gearhead" is selected, the main unit will be delivered unassembled. The customer should assemble the main unit by
following instructions on the included assembly procedure manual. P.11-097
Ordering 1Part - - - Motor Selection - 7Belt -
Example Number 2B 3L 4Output - 5Specification - 6Gearhead Reduction Ratio Specification 8Motor
E-CVSJA - 100 - 500 - 25 - SCM - 25 - H9 - G with Screw / Roller Carriers Silicon Bearings / Bearings
For No Belt E-CVSJA - 100 - 500 - 25 - INV - 25 - J - G
For No Motor, E-CVSJA - 100 - 500 - 25 - NM - NH - H9 - R
Gearhead P.11-119
Ordering 1Part Motor Selection 7Belt 8
Alterations Example Number - 2B - 3L - 4Output - 5Specification - 6Gearhead Reduction Ratio - Specification - Motor - Alteration
E-CVSJA - 100 - 500 - 25 - SCM - 25 - H9 - G - MP170 Sprocket Rollers Placon Rollers / Free Rollers /
Alterations Code Spec.
Specify Drive Section Position Transfer Direction P.11-125
The drive section position can be changed. 11
MP Ordering Code MP170 155≤MP≤L-235
*Minimum value of L is 390
Can only be specified for the center drive type.
MP Rollers / Cam Followers Conveyors / Flat Belts /
Mounting Bracket for Speed Controller
Mounting bracket for speed controller is
SCB included.
Ordering Code SCB
QConveying Capacity QGearhead Reduction Ratio - Speed Correspondence Table
E May decrease depending on load condition. *Reference value
Gearhead Flat Belt Speed (m/min)
Reduction Ratio SCM Variable Speed Motor INV Induction Motor
Transfer Weight (Unit/Kg) 12.5 17.0~28.3 35.2
25.4~42.4
5
52.8
7.5
12.7~21.2
26.4
10
21.1
10.2~17.0
15
8.5~14.1
17.6
14.7
7.1~11.8
18
25
30
8.8
4.2~7.1
36 5.1~8.5 10.6
3.5~5.9
7.3
50 2.5~4.2 5.3
60 2.1~3.5 4.4
Flat Belt Speed (m/min) 75 1.7~2.8 3.5
E This graph shows conveying capacity 90 1.4~2.4 2.9
with horizontal conditions. 100 1.3~2.1 2.6
E Conveying capacity varies depending on 120 1.1~1.8 2.2
usage conditions.
E When a variable speed motor is selected, 150 0.8~1.4 1.8
the conveying capacity will not increase 180 0.7~1.2 1.5
as the speed decreases.
11-027 Conveyors 11-028