Page 333 - MiSUMi 2025

Part Number 4L Number Basic Load Rating Axial Twisting Applicable Support Units
of
2Screw
1Type Shaft O.D. 3Lead (1mm increments) Y Circuits C (Dynamic) C (Static) Clearance Direction Shape Fixed side Support side
model
kN
model
kN
Square Type C-TEK12 C-TEF12
05 Round Type C-TFK12 C-TFF12
Short Type E-TLK12 E-TLF12
3 turns 3.6 7.4 Square Type C-TEK12 C-TEF12
15
0.015
C-KBS (16)* 10 150~1100 L-62 or Less Right Round Type C-TFK12 C-TFF12
Short Type E-TLK12 E-TLF12
Square Type C-TEK12 C-TEF12
1.8
20 turns 3.0 7.1 Round Type C-TFK12 C-TFF12
Short Type E-TLK12 E-TLF12
3 *The Y dimension must be larger than the full length of the nut kgf=N×0.101972 3
*C-KBS1505 / 1510 have the actual dimension diameter of φ16.
Ball Screws / Lead Screws Ordering Part Number (1Type · 2Screw Shaft O.D. · 3Lead) - - 150 Lead Screws Ball Screws /
4L
Example
C-KBS1505
QFixed side
Alterations
Alterations Code Spec.
6 Wrench Flats on Fixed Adds wrench flats on the fixed
Ordering Part Number (1Type · 2Screw Shaft O.D. · 3Lead) - 4L - (NC·KC…etc.) Side side shaft end.
Rolled Ball Screws QSupport side 10-0.2 32 7 5 SZC E Ball bearings will fall out if the Screws Rolled Ball
Example
Ordering Code SZC
- 245 -
C-KBS1505
KC10
ball nut crosses the wrench flats.
0
E The nut may not be moved
Alterations
Area. Note that when selecting.
1 No Machining on Support Code Spec. Incomplete Hardened Area within the Incomplete Hardened
P.03-009 Side Shaft End No machining added on the 7 Keyway on Fixed Side Adds a keyway on the fixed side P.03-009
shaft end.
Shaft End
Precision Ball Screws machining is L NC support side shaft end. KC KC When specified simultaneously Screws Precision Ball
Standard
3≤KC≤14
When
Ordering Code NC
with Q, 3≤KC≤F-1
specified
KC=1mm increments
Ordering Code KC10
Reversed
Shaft End
P.03-027 2 Ball Nut Orientation RLC Changes the nut direction. 8 Keyway on Fixed Side The machining position of P.03-027
keyways at fixed side shaft end
(Fixed side)
(Support side)
can be specified. (Keyway size
Ball Screw Supports / Motor Brackets 3 Change K S KLC 3≤K≤13 K+S≤14 Motor Brackets Ball Screw Supports /
Standard
Ordering Code RLC
is the same as KC.)
When specified simultaneously
with Q, 3≤K≤28
No Retaining Ring
K+S≤F-1
Groove on Support Side
Shaft End
Ordering Code KLC-K5-S3
P.03-047 machining is RNC No Retaining Ring Groove on 9 Flat Machined on Fixed K, S=1mm increments P.03-047
Support Side Shaft End.
Standard
Ordering Code RNC
When
Adds a flat on the fixed side
Lead Screws 4 Change the length of the Change the length of the SC 0.5 SC 5≤SC≤14 Lead Screws
Side Shaft End
shaft end.
specified
When specified simultaneously
support side shaft end
with Q, 5≤SC≤F-1
support side shaft end.
SC=1mm increments
9.15
FC=1mm increments
P.03-058 5 Change Support Side FC 11≤FC≤30 0 No machining of small Ordering Code SC10 P.03-058
Ordering Code FC20
FC
steps on the fixed side
Lead Screw Nuts machining is Qh7 GC support side. Standard NF No machining of small steps on Nuts Lead Screw
Changes the machining on the
Shaft End Machining
the fixed side
5≤G≤36
Ordering Code NF
Standard
Change
Q is selected from 8, 10 and 12
When
G=1mm increments
specified
G
Change dimensions of small
P.03-077 E Only one of 1, 3, 4 and 5 can be selected. Ordering Code GC-Q8-G20 Q Recommended L P FP Change dimensions of small P.03-077
steps on the fixed side
steps on the fixed side
Lead Screw Supports E Only one of 0 and Q can be selected. W Change dimensions of big F, P=1mm increments Supports Lead Screw
E Only one of 7, 8 and 9 can be selected.
15≤F≤30 6≤P≤10
E When W and e are specified simultaneously, no male thread will be machined
Ordering Code FP-F30-P10
F
regardless of the value specified for U in W.
E When W or e is specified, the recommended support unit may not be available.
steps on the fixed side
Please reconfirm.
P.03-079 E When specifying any alteration, the nut motion range (Y dimension) may Recommended EU Change dimensions of big steps P.03-079
on the fixed side
become shorter. Please make sure that the nut motion range is greater than the
U
13≤E≤48 10≤U≤E-3
Lead Screw Stop Plates / Position Indicators e No machining of big Ordering Code EU-E48-U20 Position Indicators Lead Screw Stop Plates /
full length of the nut.
E, U=1mm increments
E
steps male thread on the
fixed side
P.03-081 Standard NU No machining of big steps male P.03-081
thread on the fixed side
Ordering Code NU
Change
03-035 Precision Ball Screws 03-036