Page 335 - MiSUMi 2025

Part Number 4L Number Basic Load Rating Axial Twisting Applicable Support Units
of
2Screw
1Type Shaft O.D. 3Lead (1mm increments) Y Circuits C (Dynamic) C (Static) Clearance Direction Shape Fixed side Support side
model
kN
kN
model
Square Type C-TEK15 C-TEF15
05 4 turns 4.3 10.3 Round Type C-TFK15 C-TFF15
Short Type E-TLK15 E-TLF15
Square Type C-TEK15 C-TEF15
0.015
C-KBS 20 10 200~1500 L-82 3 turns 4.9 10.6 or Less Right Round Type C-TFK15 C-TFF15
Short Type E-TLK15 E-TLF15
Square Type C-TEK15 C-TEF15
1.8
20 turns 4.3 10.3 Round Type C-TFK15 C-TFF15
Short Type E-TLK15 E-TLF15
3 *The Y dimension must be larger than the full length of the nut kgf=N×0.101972 3
4L
Ordering Part Number (1Type · 2Screw Shaft O.D. · 3Lead) - - 200
Ball Screws / Lead Screws Alterations QFixed side Lead Screws Ball Screws /
Example
C-KBS2005
Spec.
Alterations
6 Wrench Flats on Fixed Code Adds wrench flats on the fixed
Ordering Part Number (1Type · 2Screw Shaft O.D. · 3Lead) - 4L - (FC·KC…etc.) Side side shaft end.
Ordering Code SZC
Example C-KBS2005 - 245 - KC10 SZC E Ball bearings will fall out if the ball
Rolled Ball Screws QSupport side Code Spec. Incomplete Hardened Area E The nut may not be moved Screws Rolled Ball
nut crosses the wrench flats.
9 6
0
35
16 -0.25
within the Incomplete Hardened
Alterations
Area. Note that when selecting.
No Machining on Support
1
Shaft End
shaft end.
P.03-009 Side Shaft End NC No machining added on the 7 Keyway on Fixed Side KC Adds a keyway on the fixed side P.03-009
4≤KC≤19
Standard
support side shaft end.
Precision Ball Screws machining is L 8 Keyway on Fixed Side with Q, 4≤KC≤F-1 Screws Precision Ball
When specified simultaneously
When
Ordering Code NC
KC
specified
KC=1mm increments
Ordering Code KC15
Ball Nut Orientation
2
Reversed
keyways at fixed side shaft end
(Support side)
can be specified. (Keyway size is
P.03-027 Standard (Fixed side) RLC Changes the nut direction. Shaft End The machining position of P.03-027
Ordering Code RLC
the same as KC.)
Ball Screw Supports / Motor Brackets 3 No Retaining Ring No Retaining Ring Groove on K S KLC When specified simultaneously Motor Brackets Ball Screw Supports /
4≤K≤18 K+S≤19
Change
with Q, 4≤K≤34
K+S≤F-1
Groove on Support Side
Shaft End
K, S=1mm increments
Ordering Code KLC-K7-S2
Standard
Ordering Code RNC
When
P.03-047 machining is RNC Support Side Shaft End. 9 Flat Machined on Fixed Adds a flat on the fixed side shaft P.03-047
specified Changes the machining on the Side Shaft End end.
Lead Screws machining is GC support side. SC 0.5 SC When specified simultaneously Lead Screws
5≤SC≤19
Change Support Side
4
Shaft End Machining
with Q, 5≤SC≤F-1
5≤G≤45
Standard
SC=1mm increments
Q is selected from 10, 12 and 15
When
Ordering Code SC7
Ordering Code GC-Q10-G20
P.03-058 specified Qh7 G G=1mm increments 0 No machining of small P.03-058
steps on the fixed side
5 Change the length of Change the length of the support Standard No machining of small steps on
Lead Screw Nuts end FC 10.15 FC 12≤FC≤30 Change L NF Ordering Code NF Nuts Lead Screw
the support side shaft
the fixed side
side shaft end.
FC=1mm increments
Ordering Code FC20
Change dimensions of small
steps on the fixed side
P.03-077 E Only one of 1, 3, 4 and 5 can be selected. Q Recommended P FP Change dimensions of small P.03-077
steps on the fixed side
E Only one of 7, 8 and 9 can be selected.
Lead Screw Supports E When W and e are specified simultaneously, no male thread will be machined W Change dimensions of big F, P=1mm increments Supports Lead Screw
20≤F≤36 8≤P≤12
E Only one of 0 and Q can be selected.
Ordering Code FP-F36-P12
regardless of the value specified for U in W.
F
E When W or e is specified, the recommended support unit may not be available.
Please reconfirm.
steps on the fixed side
on the fixed side
become shorter. Please make sure that the nut motion range is greater than the
P.03-079 E When specifying any alteration, the nut motion range (Y dimension) may Recommended EU Change dimensions of big steps P.03-079
U
13≤E≤60 10≤U≤E-3
full length of the nut.
Lead Screw Stop Plates / Position Indicators e No machining of big Ordering Code EU-E60-U20 Position Indicators Lead Screw Stop Plates /
E, U=1mm increments
E
steps male thread on the
fixed side
thread on the fixed side
P.03-081 Standard NU No machining of big steps male P.03-081
Ordering Code NU
Change
03-037 Precision Ball Screws 03-038