Page 925 - MiSUMi 2025

2B 3L Motor Selection Conveyors
1Part 7Belt Specification P.11-007
Number 10mm 5mm 4Output 5Specification 6Gearhead (Not specified: material is PU) 8Motor
increments increments (W) Reduction Ratio
SCM H9 (General Purpose·Green) G Flat Belts
E-CVSFB (Single-phase 220V W9 (General Purpose·White) (GPG Flat Belt Pulleys /
(Crowned Variable Speed Motor) 5 7.5 10 12.5 15 18 U5 (For Sliding·Green) Motor)
25 30 36 50 60 75
Roller) 25 INV 90 100 120 150 180 S5 (For Sliding·White) J P.11-071
D9 (Antistatic·Black)
E-CVSFD 80~400 320~3000 40 (3-Phase 220V F12 (For Food Transfer·White) (JSCC
60
Motor)
(With 90 Induction Motor) O14 (Oil Resistant·Green)
Meandering Q10 (For Inclined Transfer·Green) Guide Rollers Urethane Molded Bearings / Urethane Molded Rollers /
Prevention NM NH Y12 (General Purpose·Yellow PVC) R
Crosspieces) (No Motor) (No Gearhead) V12 (General Purpose·Red PVC) (No Motor,
J (No Belt) Gearhead) P.11-085
EBelt thickness is a nominal value and the actual thickness is one-tenth of the nominal value, measured in millimeters, except for D9.
EThe oil-resistant specification applies only to the conveying surface. If oil comes into contact with the back side of the belt, it may become unusable.
EIf a stepper motor or servo motor is required for automatic control, the type with no motor and gearhead can be selected. Cam Followers Ball Rollers /
EWhen "No motor, gearhead" is selected, the motor mounting hole pitch will vary depending on the motor's power rating.
E When "No motor, gearhead" is selected, the main unit will be delivered unassembled. The customer should assemble the main unit by
following instructions on the included assembly procedure manual. P.11-097
EFor products with a total length from 2.8m, the delivery time may be longer.
Ordering 1Part Motor Selection 7Belt
Example Number - 2B - 3L - 4Output - 5Specification - 6Gearhead Reduction Ratio - Specification - 8Motor with Screw / Roller Carriers Silicon Bearings / Bearings
E-CVSFB - 150 - 1000 - 25 - SCM - 25 - H9 - G
For No Belt E-CVSFB - 150 - 1000 - 25 - INV - 25 - J - G
For No Motor, E-CVSFB - 150 - 1000 - 25 - NM - NH - H9 - R P.11-119
Gearhead
Ordering 1Part Motor Selection 7Belt
Example - 2B - 3L - - - 8 - Alteration
Alterations Number 4Output - 5Specification - 6Gearhead Reduction Ratio Specification Motor Sprocket Rollers Placon Rollers / Free Rollers /
E-CVSFB - 150 - 1000 - 25 - SCM - 25 - H9 - G - MK
Alterations Code Spec. P.11-125
Motor Position Reversed 11
Motor Transfer Direction The motor position can be changed.
MK Ordering Code MK
Can only be designated for the head drive type.
Motor
Mounting Bracket for Speed Controller Rollers / Cam Followers Conveyors / Flat Belts /
Mounting bracket for speed controller is
SCB included.
Ordering Code SCB

QConveying Capacity QGearhead Reduction Ratio - Speed Correspondence Table
E May decrease depending on load condition. *Reference value
Gearhead Flat Belt Speed (m/min)
Reduction Ratio SCM Variable Speed INV Induction Motor
Transfer Weight (Unit/Kg) 12.5 20.3~33.9 42.2
Motor
5
30.5~50.9
63.3
7.5
31.7
15.3~25.4
10
25.3
12.2~20.3
15
10.2~17.0
21.1
18
6.1~10.2
12.7
25
30 8.5~14.1 17.6
10.6
5.1~8.5
36 4.2~7.1 8.8
50 3.1~5.1 6.3
60 2.5~4.2 5.3
Flat Belt Speed (m/min) 75 2.0~3.4 4.2
E This graph shows conveying capacity 90 1.7~2.8 3.5
with horizontal conditions.
E Conveying capacity varies depending on 100 1.5~2.5 3.2
usage conditions. 120 1.3~2.1 2.6
E When a variable speed motor is selected, 150 1.0~1.7 2.1
the conveying capacity will not increase 180 0.8~1.4 1.8
as the speed decreases.
11-041 Conveyors 11-042