Page 921 - MiSUMi 2025

2B 3L Motor Selection Conveyors
1Part 7Belt Specification P.11-007
Number 10mm 5mm 4Output 5Specification 6Gearhead (Not specified: material is PU) 8Motor
increments increments (W) Reduction Ratio
E-CVSFA SCM 5 7.5 10 12.5 15 18 H9 (General Purpose·Green) G Flat Belts Flat Belt Pulleys /
25 30 36 50 60 75
6
(Single-phase 220V
(Crowned 25 Variable Speed Motor) 90 100 120 150 180 W9 (General Purpose·White) (GPG
U5 (For Sliding·Green)
Roller) 40 S5 (For Sliding·White) Motor)
INV Note: 5~10 not D9 (Antistatic·Black) J P.11-071
E-CVSFC 70~300 190~2000 Note: 6 not (3-Phase 220V applicable for 6W F12 (For Food Transfer·White) (JSCC
Motor)
(With applicable Induction Motor) Motor O14 (Oil Resistant·Green)
Q10 (For Inclined Transfer·Green)
for
Meandering Induction Y12 (General Purpose·Yellow PVC) R Guide Rollers Urethane Molded Bearings / Urethane Molded Rollers /
Prevention Motor NM NH V12 (General Purpose·Red PVC) (No Motor,
Crosspieces) (No Motor) (No Gearhead) J (No Belt) Gearhead) P.11-085
EBelt thickness is a nominal value and the actual thickness is one-tenth of the nominal value, measured in millimeters, except for D9.
EThe oil-resistant specification applies only to the conveying surface. If oil comes into contact with the back side of the belt, it may become unusable.
EIf a stepper motor or servo motor is required for automatic control, the type with no motor and gearhead can be selected. Cam Followers Ball Rollers /
EWhen "No motor, gearhead" is selected, the motor mounting hole pitch will vary depending on the motor's power rating.
E When "No motor, gearhead" is selected, the main unit will be delivered unassembled. The customer should assemble the main unit by
following instructions on the included assembly procedure manual. P.11-097
Ordering 1Part - 2B - 3L - Motor Selection - 7Belt - 8Motor
Example Number 4Output - 5Specification - 6Gearhead Reduction Ratio Specification with Screw / Roller Carriers Silicon Bearings / Bearings
E-CVSFA - 200 - 1000 - 25 - SCM - 25 - H9 - G
For No Belt E-CVSFA - 200 - 1000 - 25 - INV - 25 - J - G
For No Motor, E-CVSFA - 200 - 1000 - 25 - NM - NH - H9 - R P.11-119
Gearhead
Ordering 1Part Motor Selection 7Belt 8
Alterations Example Number - 2B - 3L - 4Output - 5Specification - 6Gearhead Reduction Ratio - Specification - Motor - Alteration
E-CVSFV - 200 - 1000 - 25 - SCM - 25 - H9 - G - MK Sprocket Rollers Placon Rollers / Free Rollers /
Alterations Code Spec.
Motor Position Reversed P.11-125
Motor Transfer Direction The motor position can be changed. 11
MK Ordering Code MK
Can only be designated for the head drive type.
Motor
Mounting Bracket for Speed Controller Rollers / Cam Followers Conveyors / Flat Belts /
Mounting bracket for speed controller is
SCB included.
Ordering Code SCB

QConveying Capacity QGearhead Reduction Ratio - Speed Correspondence Table
E May decrease depending on load condition. *Reference value
Flat Belt Speed (m/min)
Gearhead
Reduction Ratio SCM Variable Speed INV Induction Motor
Motor
Transfer Weight (Unit/Kg) 12.5 20.3~33.9 42.2
5
30.5~50.9
63.3
7.5
15.3~25.4
31.7
10
12.2~20.3
25.3
21.1
10.2~17.0
15
18
25
6.1~10.2
12.7
5.1~8.5
10.6
30 8.5~14.1 17.6
36 4.2~7.1 8.8
50 3.1~5.1 6.3
Flat Belt Speed (m/min) 60 2.5~4.2 5.3
E This graph shows conveying capacity 75 2.0~3.4 4.2
with horizontal conditions. 90 1.7~2.8 3.5
E Conveying capacity varies depending on 100 1.5~2.5 3.2
usage conditions.
E When a variable speed motor is selected, 120 1.3~2.1 2.6
the conveying capacity will not increase 150 1.0~1.7 2.1
as the speed decreases. 180 0.8~1.4 1.8
11-037 Conveyors 11-038