Page 917 - MiSUMi 2025

2B 3L Motor Selection Conveyors
1Part 7Belt Specification P.11-007
Number 10mm 5mm 4Output 5Specification 6Gearhead (Not specified: material is PU) 8Motor
increments increments (W) Reduction Ratio
SCM G Flat Belts Flat Belt Pulleys /
(Single-phase 220V H20 (General Purpose·Green PVC) (GPG
Variable Speed Motor) 5 7.5 10 12.5 15 18 W20 (General Purpose·White PVC) Motor)
25 30 36 50 60 75
E-CVSE 60 INV 90 100 120 150 180 U13 (For Sliding·Green PVC) J P.11-071
S13 (For Sliding·White PVC)
(With 90 (3-Phase 220V D20 (Antistatic·Green PVC) (JSCC
Meandering 80~600 550~3000 120 F15 (For Food Transfer·White PU) Motor)
Prevention Induction Motor)
Crosspieces) 200 O14 (Oil Resistant·Green PU) Guide Rollers Urethane Molded Bearings / Urethane Molded Rollers /
NM NH Y20 (General Purpose·Yellow PVC) R
V20 (General Purpose·Red PVC) (No Motor,
(No Motor) (No Gearhead) J (No Belt) Gearhead) P.11-085
EBelt thickness is a nominal value and the actual thickness is one-tenth of the nominal value, measured in millimeters, except for D9.
EThe oil-resistant specification applies only to the conveying surface. If oil comes into contact with the back side of the belt, it may become unusable. Cam Followers
EIf a stepper motor or servo motor is required for automatic control, the type with no motor and gearhead can be selected. Ball Rollers /
EWhen "No motor, gearhead" is selected, the motor mounting hole pitch will vary depending on the motor's power rating.
E When "No motor, gearhead" is selected, the main unit will be delivered unassembled. The customer should assemble the main unit by
following instructions on the included assembly procedure manual. P.11-097
EFor products with a total length from 2.8m, the delivery time may be longer.
Ordering 1Part Motor Selection 7Belt with Screw / Roller Carriers Silicon Bearings / Bearings
Example Number - 2B - 3L - 4Output - 5Specification - 6Gearhead Reduction Ratio - Specification - 8Motor
E-CVSE - 300 - 1500 - 60 - SCM - 25 - H20 - G
For No Belt E-CVSE - 300 - 1500 - 60 - INV - 25 - J - G P.11-119
For No Motor, E-CVSE - 300 - 1500 - 60 - NM - NH - H20 - R
Gearhead
Ordering 1Part Motor Selection 7Belt 8
Alterations Example Number - 2B - 3L - 4Output - 5Specification - 6Gearhead Reduction Ratio - Specification - Motor - Alteration Sprocket Rollers Placon Rollers / Free Rollers /
E-CVSE - 300 - 1500 - 60 - SCM - 25 - H20 - G - MK
Alterations Code Spec. P.11-125
Motor Position Reversed 11
Motor Transfer Direction The motor position can be changed.
MK Ordering Code MK
Can only be designated for the head drive type.
Motor Rollers / Cam Followers Conveyors / Flat Belts /
Mounting Bracket for Speed Controller
Mounting bracket for speed controller is
SCB included.
Ordering Code SCB

QConveying Capacity QGearhead Reduction Ratio - Speed Correspondence Table
E May decrease depending on load condition. *Reference value
Gearhead Flat Belt Speed (m/min)
Reduction Ratio SCM Variable Speed INV Induction Motor
Motor
Transfer Weight (Unit/Kg) 12.5 24.4~40.7 50.6
5
76
36.6~61.0
7.5
38
10
18.3~30.5
14.6~24.4
30.4
12.2~20.3
15
25.3
10.2~17.0
18
21.1
25
6.1~10.2
12.7
30
36 7.3~12.2 15.2
10.6
5.1~8.5
50 3.7~6.1 7.6
60 3.1~5.1 6.3
Flat Belt Speed (m/min) 75 2.4~4.1 5.1
E This graph shows conveying capacity 90 2.0~3.4 4.2
with horizontal conditions.
E Conveying capacity varies depending on 100 1.8~3.1 3.8
usage conditions. 120 1.5~2.5 3.2
E When a variable speed motor is selected, 150 1.2~2.0 2.5
the conveying capacity will not increase 180 1.0~1.7 2.1
as the speed decreases.
11-033 Conveyors 11-034