Page 919 - MiSUMi 2025

2B 3L Motor Selection Conveyors
1Part 7Belt Specification P.11-007
Number 10mm 5mm 4Output 5Specification 6Gearhead (Not specified: material is PU) 8Motor
increments increments (W) Reduction Ratio
SCM Flat Belts Flat Belt Pulleys /
(Single-phase 220V H20 (General Purpose·Green PVC) G
Variable Speed Motor) 5 7.5 10 12.5 15 18 W20 (General Purpose·White PVC) (GPG Motor)
25 30 36 50 60 75
J
E-CVSG INV 90 100 120 150 180 U13 (For Sliding·Green PVC) (JSCC P.11-071
S13 (For Sliding·White PVC)
(With 120 (3-Phase 220V D20 (Antistatic·Green PVC)
Meandering 100~800 600~3000 Motor)
Prevention 200 Induction Motor) F15 (For Food Transfer·White PU)
Crosspieces) O14 (Oil Resistant·Green PU) Guide Rollers Urethane Molded Bearings / Urethane Molded Rollers /
NM NH Y20 (General Purpose·Yellow PVC) R
V20 (General Purpose·Red PVC) (No Motor,
(No Motor) (No Gearhead) J (No Belt) Gearhead) P.11-085
EBelt thickness is a nominal value and the actual thickness is one-tenth of the nominal value, measured in millimeters, except for D9.
EThe oil-resistant specification applies only to the conveying surface. If oil comes into contact with the back side of the belt, it may become unusable. Cam Followers
EIf a stepper motor or servo motor is required for automatic control, the type with no motor and gearhead can be selected. Ball Rollers /
EWhen "No motor, gearhead" is selected, the motor mounting hole pitch will vary depending on the motor's power rating.
E When "No motor, gearhead" is selected, the main unit will be delivered unassembled. The customer should assemble the main unit by
following instructions on the included assembly procedure manual. P.11-097
EFor products with a total length from 2.8m, the delivery time may be longer.
Ordering 1Part Motor Selection 7Belt with Screw / Roller Carriers Silicon Bearings / Bearings
Example Number - 2B - 3L - 4Output - 5Specification - 6Gearhead Reduction Ratio - Specification - 8Motor
E-CVSG - 300 - 2000 - 120 - SCM - 25 - H20 - G
For No Belt E-CVSG - 300 - 2000 - 120 - INV - 25 - J - G P.11-119
For No Motor, E-CVSG - 300 - 2000 - 120 - NM - NH - H20 - R
Gearhead
Ordering 1Part Motor Selection 7Belt 8
Alterations Example Number - 2B - 3L - 4Output - 5Specification - 6Gearhead Reduction Ratio - Specification - Motor - Alteration Sprocket Rollers Placon Rollers / Free Rollers /
E-CVSG - 300 - 2000 - 120 - SCM - 25 - H20 - G - MK
Alterations Code Spec. P.11-125
Motor Position Reversed 11
Motor Transfer Direction The motor position can be changed.
MK Ordering Code MK
Can only be designated for the head drive type.
Motor Rollers / Cam Followers Conveyors / Flat Belts /
Mounting Bracket for Speed Controller
Mounting bracket for speed controller is
SCB included.
Ordering Code SCB

QConveying Capacity QGearhead Reduction Ratio - Speed Correspondence Table
E May decrease depending on load condition. *Reference value
Flat Belt Speed (m/min)
Gearhead
Reduction Ratio SCM Variable Speed INV Induction Motor
Motor
Transfer Weight (Unit/Kg) 12.5 27.1~45.2 56.3
5
40.7~67.8
84.4
7.5
20.3~33.9
42.2
10
16.3~27.1
33.8
28.1
13.6~22.6
15
18
25
8.1~13.6
16.9
6.8~11.3
14.1
30 11.3~18.8 23.4
36 5.7~9.4 11.7
50 4.1~6.8 8.4
Flat Belt Speed (m/min) 60 3.4~5.7 7.0
E This graph shows conveying capacity 75 2.7~4.5 5.6
with horizontal conditions. 90 2.3~3.8 4.7
E Conveying capacity varies depending on 100 2.0~3.4 4.2
usage conditions. 120 1.7~2.8 3.5
E When a variable speed motor is selected, 150 1.4~2.3 2.8
the conveying capacity will not increase
as the speed decreases. 180 1.1~1.9 2.3
11-035 Conveyors 11-036