Page 317 - MiSUMi 2025

Ordering Part Number (1Type · 2Screw Shaft O.D. · 3Lead) - 4L - (FC·SC…etc.)
Alterations Example C-TBSE1002 - 280 - SC5
QSupport side QFixed side
Alterations Code Spec. Alterations Code Spec.
1 No Machining on Support 5 Wrench Flats on Fixed Side Adds wrench flats on the fixed
Side Shaft End side shaft end.
No machining added on the Ordering Code SZC
Standard E Ball bearings will fall out if the
NC support side shaft end. 5 5 SZC
When 0 ball nut crosses the wrench flats.
machining Ordering Code NC 8-0.2 30 E The nut may not be moved within
is specified the Incomplete Hardened Area.
L Incomplete Hardened Area Note that when selecting.
2 Ball Nut Orientation 6 Keyway on Fixed Side Adds a keyway on the fixed side shaft end.
Reversed Shaft End 2≤KC≤8
(Support side) (Fixed side) RLC Changes the nut direction. -0.004 -0.029 KC When specified simultaneously
with 0, 2≤KC≤F-1
3 Standard Ordering Code RLC 2 XP=5 is not applicable 3
1.2
KC
Change 7 Keyway on Fixed Side KC=1mm increments
Ordering Code KC5
The machining position of keyways at
No Retaining Ring Groove
3
Ball Screws / Lead Screws on Support Side Shaft End RNC No Retaining Ring Groove on Shaft End S KLC fixed side shaft end can be specified. Lead Screws Ball Screws /
(Keyway size is the same as KC.)
Support Side Shaft End.
2≤K≤7 K+S≤8
Standard
Ordering Code RNC
When specified simultaneously
When
machining
K
with 0, 2≤K≤16 K+S≤F-1
is specified
K, S=1mm increments
Change the length of the
4
support side shaft end Change the length of the XP=5 is not applicable
Ordering Code KLC-K5-S2
support side shaft end. 8 Flat Machined on Fixed Adds a flat on the fixed side shaft end.
FC
10≤FC≤20
Rolled Ball Screws E Only one of 1, 3 and 4 can be selected. Ordering Code FC20 SC 0.5 SC When specified simultaneously Screws Rolled Ball
Side Shaft End
5≤SC≤8
FC=1mm increments
6.8
FC
with 0, 5≤SC≤F-1
SC=1mm increments
Ordering Code SC7
No machining of small
E 9 and 0 cannot be specified simultaneously.
P.03-009 E Only one of 6, 7 and 8 can be selected. 9 Standard No machining of small steps on P.03-009
steps on the fixed side
E When Q and W are specified simultaneously, no male thread will be machined
Precision Ball Screws E When Q or W is specified, the recommended support unit may not be available. Change L NF the fixed side Screws Precision Ball
regardless of the value specified for U in Q.
Ordering Code NF
Please reconfirm.
E When specifying any alteration, the nut motion range (Y dimension) may
become shorter. Please make sure that the nut motion range is greater than the
Change dimensions of small
steps on the fixed side
P.03-027 full length of the nut. 0 Recommended P FP Change dimensions of small P.03-027
steps on the fixed side
Ball Screw Supports / Motor Brackets Q Change dimensions of big F, P=1mm increments Motor Brackets Ball Screw Supports /
9≤F≤18 5≤P≤6
Ordering Code FP-F18-P6
F
steps on the fixed side
P.03-047 Recommended EU Change dimensions of big steps P.03-047
on the fixed side
U
11≤E≤35 8≤U≤E-3
Lead Screws No machining of big steps male E, U=1mm increments Lead Screws
Ordering Code EU-E35-U10
E
P.03-058 W thread on the fixed side No machining of big steps male P.03-058
Standard NU thread on the fixed side
Lead Screw Nuts Change Nuts Lead Screw
Ordering Code NU
P.03-077 P.03-077
Lead Screw Supports Supports Lead Screw
P.03-079 P.03-079
Lead Screw Stop Plates / Position Indicators Position Indicators Lead Screw Stop Plates /
P.03-081 How to search Search on MISUMI official website Step 1 Step 2 Select Economy series P.03-081
on website 1 E-TBSE 2 ball screw c7 # MISUMI
By Type Search on MISUMI official website and get your product By Keyword # Only MISUMI Economy series
03-019 Rolled Ball Screws 03-020