Page 895 - MiSUMi 2025

Economy series Belt Adjustment Manual Belt Adjustment Manual Economy series
Conveyors Conveyors Conveyors

Note 1: Belt tensioning and meandering adjustments have been made before Conveyors leave the factory. Sometimes meandering readjustment is
required due to vibration during transportation. In such case, the user should make meandering adjustment following the procedure below. P.11-007
Note 2: During meandering adjustment, keep the Conveyor running slowly. If a Conveyor runs at a high speed before meandering adjustment, the
belt will shake violently from side to side, resulting in roughed end surface of the belt.
Head Drive Belt Meandering Adjustment Method (E-SV series) Center Drive Belt Meandering Adjustment Method (E-SV series) Flat Belts Flat Belt Pulleys /

P.11-071

Belt Travel Belt Travel Direction Guide Rollers Urethane Molded Bearings / Urethane Molded Rollers /
Direction
Belt Travel Direction
Tension Holder Screw P.11-085
Tension Holder Tension Screw Tension Screw Tension Screw Fixing Nut
1If the belt meanders towards one side, run the Conveyor slowly, and loosen the tension holder screws on both sides with a wrench; 1Check that the tension screw fixing nuts are not loose, taking the belt travel direction as a reference. If any nut is loose, tighten it. Cam Followers Ball Rollers /
Then, make meandering adjustment using the tension screws on the side towards which the belt meanders. If the belt meanders towards one side, run the Conveyor slowly, and loosen the tension screw fixing nuts with a wrench;
*Avoid contact of either side of the belt with the tension holder. Then, make meandering adjustment using the tension screws on the side towards which the belt meanders.
*Avoid contact of either side of the belt with the tension holder.
When adjusting When adjusting When adjusting When adjusting P.11-097
in the direction of arrow B
in the direction of arrow A Belt Travel Direction Belt Travel Direction in the direction of arrow A Belt Travel Direction in the direction of arrow B with Screw / Roller Carriers Silicon Bearings / Bearings

Belt Travel Direction
A A P.11-119
B B
Tension Screw Tension Screw Sprocket Rollers Placon Rollers / Free Rollers /
Tension Screw Tension Screw
Clockwise Counterclockwise Clockwise Counterclockwise
2When the belt moves in the direction of arrow A or B, turn the tension screws in the direction indicated above. 3After meandering adjustment, 2When the belt moves in the direction of arrow A or B, turn the tension screws in the direction indicated above. 3After meandering adjustment, P.11-125
Check that the belt is moving slowly in the direction of the arrow until it stops shaking from side to side. tighten the tension holder screws. Check that the belt is moving slowly in the direction of the arrow until it stops shaking from side to side. tighten the tension screw fixing nuts. 11
*The belt should be adjusted appropriately in the reverse direction depending on the tension of the belt. *The belt should be adjusted appropriately in the reverse direction depending on the tension of the belt.
*When the belt is adjusted in the reverse direction, the tension screws should also be turned in the reverse direction. *When the belt is adjusted in the reverse direction, the tension screws should also be turned in the reverse direction.

Head Drive Belt Meandering Adjustment Method (E-CV series) Center Drive Belt Meandering Adjustment Method (E-CV series) Rollers / Cam Followers Conveyors / Flat Belts /

Belt Travel Direction

Belt Travel
Direction Tension Screw Fixing Nut
Tension Screw
Tension Screw
1Check that the tension screw fixing nuts are not loose, taking the belt travel direction as a reference. If any nut is loose, tighten it.
If the belt meanders towards one side, run the Conveyor slowly, and loosen the tension screw fixing nuts with a wrench; Then,
1If the belt meanders towards one side, run the Conveyor slowly, and make meandering adjustment using the tension screws on the make meandering adjustment using the tension screws on the side towards which the belt meanders.
side towards which the belt meanders. *Avoid contact of either side of the belt with the tension holder.
*Avoid contact of either side of the belt with the tension holder. When adjusting in the direction of When adjusting in the direction of When adjusting in the direction of When adjusting in the direction of
When adjusting When adjusting Belt Travel Direction arrow A Belt Travel Direction arrow B arrow A arrow B
in the direction of arrow A in the direction of arrow B Belt Travel Direction Belt Travel Direction

A
A B
A
B Tension Screw Tension Screw
Tension Screw Tension Screw Tension Screw Clockwise Tension Screw Clockwise Counterclockwise

Clockwise Counterclockwise Adjustment of tension screws on side plate Adjustment of tension screws on adjusting device
2When the belt moves in the direction of arrow A or B, turn the tension screws in the direction indicated above. 3After meandering adjustment,
2When the belt moves in the direction of arrow A or B, turn the tension screws in the direction indicated above. 3After meandering adjustment, Check that the belt is moving slowly in the direction of the arrow until it stops shaking from side to side. tighten the tension screw fixing nuts.
Check that the belt is moving slowly in the direction of the arrow until it stops shaking from side to side. tighten the tension holder screws.
*The belt should be adjusted appropriately in the reverse direction depending on the tension of the belt. *The belt should be adjusted appropriately in the reverse direction depending on the tension of the belt.
*When the belt is adjusted in the reverse direction, the tension screws should also be turned in the reverse direction.
*When the belt is adjusted in the reverse direction, the tension screws should also be turned in the reverse direction.
*The two adjustment methods shown above cannot be used at the same time.
11-011 11-012