Page 1323 - MiSUMi 2025

20,25 ALUMINUM FRAME 19

Series Slot Width 6mm: Series 20, 25 Safety Fences / Related Accessories AL Frames / AL Pipe Frames / Steel Pipes /
Japanese Standard

When ordering, select Part Number and Values from Selection Steps 1~3.
12Part Number - 3L
NFS5-4060 - 1000
Rectangle shape 4-Side Slots 40 Accessories N-Series AL Frames /
4-R1 10 20 10 (2-B-4) Components Expanded
2 Frame Length Quantity P.19-009
10 ① NFS6-3030-2000 2
4-φ4.2 8 ② NFS6-3030-2000-LCH 2
8 ③ NFS6-3030-1170 3
1.5 20 ④ NFS6-3030-740 3 Accessories Economy Series AL Frames /
60
⑤ NFS6-3030-1940 6
20 ⑥ NFS6-3030-1440 5 P.19-037
⑦ NFS6-3030-1440-RDH-LDH 1
NFS5-4060
Clear Anodize 10 Brackets, Bolts, Nuts Quantity
⑧ NBLFSN6-C-SET 4x13=52
Material Length Weight Section Area Cross Sectional Moment of Inertia ⑨ NBLFSN6-SET 10 Accessories AL Pipe Frames /
A6063S-T5 50~4000mm 1.80kg/m 665mm 2 ℓ x 12.63×10 mm 4 ℓ y 27×10 mm 4 ⑩ NSJ6 2
4
4
P.19-067
Rectangle shape 4-Side Slots 40
4-R1 10 20 10 (Description)
② Add a wrench access hole on one end
10 for Single Joint connections.
8-φ4.2 Add a D Hole to each end for Joint Nuts. Accessories PE Coated Steel Pipes /
20 ⑦
⑧ Add tapped holes on brackets for
panels. Also include the screw/nut sets. P.19-070
20 80 In this example, a panel is mounted
to the side shown in the figure below.
(Surfaces except front right and bottom)
3.5 20
NFS5-4080 ⑨ Top, bottom, and middle section Accessories Safety Fences /
brackets include bolt/nut sets.
Clear Anodize 10
⑩ Single Joint Kits need with the extrusion
Material Length Weight Section Area Cross Sectional Moment of Inertia on ⑦ and ②. P.19-072
A6063S-T5 50~4000mm 2.69kg/m 994mm 2 ℓ x 18.29×10 mm 4 ℓ y 63.3×10 mm 4
4
4
Q Hole Machining Details (D Hole, S Hole, M Hole)
Ma chining direction of D, S, M holes differs depending on the frame shape and the number of slots.
(Note 1) For the D hole and M hole, the max. hole machining length is 90mm.
(Note 2) For the frames with L-shaped cross section, D, S, M hole machining is not available.
For 4-Side Slot Frames For Smooth Sided Frames
(Ex.: NEFS6-3030, NEFS6-3060) (Ex.: NEFSF6-3030, NEFST6-3030)
(D holes, S holes, M holes) 1 • For 2-Side/3-Side Slot frames, the D, M holes can be
machined vertically or horizontally. Holes are not machined
＊
on flat surfaces.
E When using the Single Joints HSJD for 2-side slot or
(D holes, S holes, M holes) ＊ 3-side slot, this hole machining will be performed.
EM holes go through.
• Place each type of frame in the same manner as indicated below.
＊
2 ①On the vertical length.
②Flat side down.
③One flat side down and another flat side right.
＊ ＊ ＊ • Any S hole cannot be machined toward the smooth surfaces.
3
For the square-shaped cross section • If the cross section is rectangle-shaped, place the frame
＊ ＊ in such a way that the longitudinal sides are vertically stood.
• The D, S, M holes can be drilled vertically or horizontally.
• If any type of hole machining is not performed in combination ＊ ＊ NEFS6-3030-500-LDH
with other types of hole machining, it is not necessary to distin- * D holes must not be machined on the
surfaces marked with this asterisk.
guish between vertical drilling and horizontal drilling.
For the rectangle-shaped cross section
• The D, S, M holes can be drilled vertically or horizontally. Place the frame in such a way that the smooth surface
is on the bottom side. For the frame with
E Place the frame in such a way that the longitudinal sides are vertically stood. rectangle-shaped cross section, however, ensure that
the longitudinal sides are vertically stood.
19-011 19-012